- October 2017 (1)
- September 2017 (4)
- August 2017 (6)
- July 2017 (9)
- April 2017 (1)
- February 2017 (2)
- December 2016 (1)
- November 2016 (2)
- October 2016 (2)
- September 2016 (2)
- August 2016 (3)
- July 2016 (5)
- June 2016 (8)
- May 2016 (8)
- April 2016 (3)
- March 2016 (1)
- February 2016 (1)
- January 2016 (1)
- December 2015 (2)
- November 2015 (2)
- October 2015 (1)
- September 2015 (1)
Tag Archives: Distressed Door Trim
In getting ideas for the type of wood trim we wanted, we browsed through our local home improvement store. We saw wood planks that looked like they came right out a centuries old barn. It’s amazing how engineered wood products these days are made to look rustic and distressed right out-of-the-box. And you can pay a pretty penny for them too! While they are quick and easy to install with little labor involved, they are still ‘engineered’ wood – meaning fake, and to us they certainly had a ‘plastic’ look going on.
In keeping with the rustic vibe, we knew right off that we were going to have to do the grunt work to achieve it. But, the trade off would be custom, one of a kind, REAL wood trim.
We started with #3 pine. Wood comes in grades, like A, B, C, and 1, 2, 3, etc.. ‘A’ grade is typically ‘clear’, as in no knots, splits, or imperfections = a beautiful piece of wood. As the grade goes higher, the quality, or clearness goes down. So a ‘C’ grade will have lots of knots, and imperfections. They are also priced accordingly – ‘A’ grade and #1 are both expensive. You get the idea. So as I said we started with a very inexpensive #3 pine with lots of imperfections, and as we were intending to beat the crud out of it, the more imperfections the better! In this project, using a beautiful, hard #1 or ‘A’ grade would have been a waste.
As you can see in the above photo, lovely imperfections! But we needed the wood to have a bit more character than this. We assembled our ‘professional’ DIY wood distressing tools and supplies 😉 ….
We used a sander scraper to round out some of the edges, a screw, a metal rod I found laying around the house left by the previous owners, a handful of rocks from the backyard, a spare wood block, and a hammer to beat it all with.
After scraping some of the edges, and sanding down splinters, I hammered the screw lengthwise as well as used the screw tip to put little holes in the wood. I laid the metal rod down at different angles and hammered it to mimic old metal strapping. Next I sorted the rocks out atop the trim, then sandwiched them with my extra wood block and pressed and rolled the block around, grinding the rocks into the trim. I varied the areas of distressing so that it wouldn’t look too uniform, giving it a more natural weathered appearance.
After distressing, I cleaned off the boards, set them up onto a couple of sawhorses for staining. We went with ‘Gunstock’ by Varathane….
We brushed it on sort of thick, and let it sit for 2 to 3 minutes. The longer it sits, the darker the color.
With disposable gloves on, Aaron and I then rubbed off the excess stain. The stain settled into all the distress marks and natural imperfections, bringing out all the character….
We loved how they turned out! The color was perfect as well, not too yellow, not too ashy, but not red either. Just a nice warm, rich brown. Want to see them installed with a bit of ‘industrial’ hardware?….stay tuned then for more of our laundry room makeover 🙂